Köla

The largest combine harvester manufacturer in Europe, Ködel & Böhm, had produced nearly half a million combine harvesters when it introduced its first combine harvester, the Köla SM 3, to the market in 1951. This was a self-propelled combine equipped with a 230 cm cutting table and a 52 hp diesel engine. Later, the SM 4 with a 10 cm wider cutting table was introduced alongside the GM 4, a pull-type combine harvester with its own engine.

The threshing drum of the SM 3 and 4 was a full 150 cm wide. The width of the single-section beater was the same. Bagging equipment was standard, and a grain tank was available at an extra cost. The height adjustment of the cutting table was hydraulic, and the height of the straw walker was adjusted with a lever from the driver's seat. The speed of the threshing drum could be adjusted steplessly. Standard grain sieves were 8, 10, 12, and 14 millimeters.

This is an automated translation. Please report any issues in the translation.

Combines

Köla SM 3 – SM 4

In 1968 the Rubin appeared on the market, taking its place in the Köla range between the Coronet and the Hydromat. It used the same Perkins engine as the Coronet, rated at 72 hp. In the parallel model, the Rubin X100, there was a 90 hp engine. Surprisingly, the engine was mounted in the old Köla fashion on the driver’s side. The cutting width was 300 cm, and the lower-powered version was also available with a 260 cm header. The threshing‐drum width (106 cm) and the dimensions of the sieve and straw walkers were considerably larger than on the Coronet, even though the overall size and price difference between the machines was small.

Shortly after the Rubin’s introduction, KHD acquired the Köla factory, and the Köla Rubin was initially renamed the Fahr Rubin. In 1972 the model designation changed to M 900, the engine was swapped out for a Deutz, and it was relocated to the rear of the grain tank.

The brochure image apparently shows some kind of prototype, since its unloading pipe isn’t recessed as on the production models. The slope of the top of the tank in the photo also doesn’t match the rounded shape familiar from the Fahr machines.

The last combine presented under the Köla name was the Corall, similar to the Rubin but with three straw walkers. It was powered by a 69 hp Perkins engine and had an 80 cm-wide threshing mechanism. Its cutting width was 250 cm. The Corall was also sold under the Fahr brand in 1971, but its production was then discontinued, and that size class was continued with Fahr-based models.

This is an automated translation. Please report any issues in the translation.

Köla Rubin, Corall

Milestones in the history of combine harvesters include the world’s first harvester equipped with a hydrostatic drive transmission, the Köla Hydromat, whose production began in 1966. Each driving wheel was powered by a hydraulic motor. There were two speed ranges: 0…10 and 0…20 km/h. The Hydromat’s engine was a 6-cylinder Perkins, whose 106 hp power was rather low compared to the rest of the harvester’s design. The threshing mechanism width was 127.5 cm. The length of the threshing drum was as much as 380 cm. Header widths were available in sizes ranging from 300 to 600 cm. The cutting height adjustment was automatic. The saddle-shaped grain tank had a volume of 2,800 liters. The Hydromat was available in the traditional red or white.

In 1969, Ködel & Böhm came under the ownership of Deutz. Slightly earlier, they had already acquired Fahr, which specialized in smaller combine harvesters. Thus, the Köla Hydromat became Fahr’s flagship model M1250. The most important change was the 140-horsepower Deutz engine. Production continued at Köla’s factory in Lauingen, where eventually the rest of Deutz-Fahr’s production was also concentrated.

This is an automated translation. Please report any issues in the translation.

Köla Hydromat

The Köla Favorit was completely replaced by the new Coronet in 1967. The design was modern and angular. The grain tank was now in its usual place and was saddle-shaped. The Perkins engine was located at the back of the tank. The driver sat in the centerline of the harvester. The cutting width was 255 cm. The cutting height adjustment was automatic; a sensor located under the header monitored the irregularities of the ground surface. The sizing of the threshing mechanism was the same as its predecessor: the width of the threshing drum was 90 cm and the diameter 56 cm. There were three threshing bars, each 300 cm long.

This is an automated translation. Please report any issues in the translation.

Köla Coronet

In 1955, Ködel & Böhmin's smaller threshing combine, the Köla Combi, was introduced to the market. It was equipped with a 34-horsepower Mercedes diesel engine. The engine was located next to the driver on the right-hand side. The cutting width was 190 cm. The height adjustment of the unloading reel was mechanically standard. The threshing drum width was 70 cm, and it had three rasp bars. In the tank version, the tank was positioned below the sack-loading platform, and the discharge pipe was at the rear of the combine, where the grain was conveyed by a horizontal auger located under the belly of the combine. In 1959, the Combi Special was introduced, featuring a 205 cm cutting table. The Combi Extra, on the other hand, was equipped with a 190 cm cutting table but had a wider front axle and larger wheels than the original Combi. Over the years, the Combis underwent quite a few upgrades, including an increase in engine power to 38 horsepower.

Also introduced in 1959 was the larger Favorit, which had a cutting width of 255 or 300 cm. Its construction was similar to the Combi, meaning it was very low-profile. However, its height was increased by 63 cm due to a high-rise grain elevator. A novelty was the Vario-System, which allowed the tank to be easily folded away when desired, directing the grain into sacks. The Favorit's threshing drum was not only wider but also had a larger diameter (56 cm). The Fordson engine initially offered 55 hp, later increased to 68 hp. Additionally, 56-horsepower Deutz or Hanomag diesels were available.

Köla machines were imported to Finland during the years 1960-66 and 1967-69.

This is an automated translation. Please report any issues in the translation.

Köla Combi, Favorit

More from this manufacturer

<p>The Köla Favorit was completely replaced by the new Coronet in 1967. The design was modern and angular. The grain tank was now in its usual place and was saddle-shaped. The Perkins engine was located at the back of the tank. The driver sat in the centerline of the harvester. The cutting width was 255 cm. The cutting height adjustment was automatic; a sensor located under the header monitored the irregularities of the ground surface. The sizing of the threshing mechanism was the same as its predecessor: the width of the threshing drum was 90 cm and the diameter 56 cm. There were three threshing bars, each 300 cm long.</p>
<p>This is an automated translation. Please report any issues in the translation.</p>


Coronet

Malli

Hinta (sis. alv)

Imported to Finland

Years

First year sold

Last year sold

Power

Power speed

Engine

Engine type

Moottorin merkki ja malli

Turbo

Teho

Iskutilavuus

Sylinterien lukumäärä

Moottorin sijainti

Polttoainesäiliön tilavuus

Ajovoimansiirron tyyppi

Nopeusalueiden lukumäärä

Neliveto

Työleveys

Leikkuuleveys

Leikkuupöydän korkeuden säätö

Syöttöruuvin harjan etäisyys terän sormien kärjestä

Terän korkeus, minimi

Terän korkeus, maksimi

Leikkuupöydän korkeuden osoitin

Säätö korkeussuunnassa

Säätö pituussuunnassa

Nopeuden säätö

Puintikelojen lukumäärä

Varstojen lukumäärä

Kelojen leveys

Kelojen nopeus, maksimi

Kelojen nopeuden säätötapa

Varstasiltojen lukumäärä

Siltojen pituudet (varstojen ulkoreunasta mitaten)

Puintivälin säätö

Puintivälin toteaminen ja mittaus

Kohlimien lukumäärä

Kohlimien leveys

Kohlimien pituus

Kohlimien pinta-ala

Ruumenpinta-ala

Siemenpinta-ala

Eturaideväli

Akseliväli

Pituus kuljetusasennossa ilman pöytää

Korkeus (ylimp. kiint. pisteeseen)

Leveys, työasennossa

Leveys, kuljetusasennossa

Maavara koneen alla (minimi)

Viljasäiliön tilavuus

Viljasäiliön tilavuus lisälaidoin

Paino työkunnossa (polttoainesäiliöt täynnä)

Jarrut

Laonnostimien lukumäärä

Ruumenseulan tyyppi

Työvalojen lukumäärä

Työvalojen tyyppi

Teho, kW/Suurimman tehon kierrosluku, r/min

Suurimman tehon kierrosluku

Iskutilavuus, cm3/Sylinterien lukumäärä, kpl

Nopeus, km/h

Työleveys (jakol. kärjestä mitattuna), cm/Leikkuuleveys, cm

Terän alin...ylin taso (korkeus maasta), cm

Laonnostokelan säätöalue, r/min

Puintikela 1 halkaisija

Puintikela 2 halkaisija

Puintikela 3 halkaisija

Puintikelojen halkaisijat, cm

Puintikelojen nopeuden säätö

Varstojen 1 tehollinen pinta-ala (kaareva pituus x kelan leveys)

Varstojen 2 tehollinen pinta-ala (kaareva pituus x kelan leveys)

Varstojen 3 tehollinen pinta-ala (kaareva pituus x kelan leveys)

Varstojen teholliset pinta-alat (kaareva pit. x kelan lev.), dm2

Kohlintilan leveys x kohlinten pituus, cm

Renkaat edessä

Renkaat takana

Displacement

Esipuhdistaja

Cyl/turbo

Läpimitta (piikk.kärk.)

Power hp DIN

Power hp ISO

Alternative hp

Fuel tank

Transmission

Gears

Speed min-max.

Cutting width

Cutting width, alternative

Myynti

Takaraideväli, cm

Reel diameter

Header length

Threshing cyl. diameter

2. cyl. diameter

Threshing cyl. width

Number of straw walkers

Etusivu

Ajoneuvot ja ympäristö

Huolto ja tekniikka

Lukijan idea

Maarakennus

Maatalous

Osastot

Metsä

Pääkirjoitus

Uutiset

Weteraani

Yritykset ja tapahtumat

Lukijan kuvat

Koneviesti

Lehdet

Konedata

Palvelut

Tilaa Koneviesti

Asiakaspalvelu

Jätä ilmoitus

Tilaa uutiskirje

Lähetä uutisvinkki

Lähetä palautetta

Lähetä oikaisupyyntö

Toimituksen yhteystiedot

Mediamyynnin yhteystiedot

Ota yhteyttä

Subscribe

Paywall

Send feedback

Welcome to the beta version of Koneviesti's new Konedata service! The service offers technical data for over 8000 tractors and combines. We are actively developing the service, so we appreciate your feedback.

Give feedback

Model	Coronet
Options
Imported to Finland	Yes
Years	1967-69
First year sold	1967
Last year sold	1969
Power	68
Engine	Perkins
Engine type	A4.236
Displacement	3860 cm³
Cyl/turbo	4
Power hp DIN	68
Alternative hp	72 hp
Fuel tank	110 l
Transmission	mech.
Gears	3
Speed min-max.	?-17,5 km/h
Cutting width	255 cm
Cutting width, alternative	300 cm
Threshing cyl. diameter	56 cm
Threshing cyl. width	90 cm
Number of straw walkers	3
Area of walkers	270 dm²
Lenght of walkers	300 cm
Straw shieve	119 dm²
Bottom shieve	94 dm²
Total screening area	213
Overall lenght	810 cm
Overall width	295 cm
Height without cabin	270 cm
Weight without cabin	4500 kg
Grain tank	17 hl
Tyres front (Finland)	18.4-26
Tyres front, alternative	14.9-26
Tyres rear (Finland)	10.00-12
Tyres rear, alternative	8.00-12
Reel forward/backw. adjustment	holes
Reel speed adjustment	converter
Threshing cyl. speed adjustment	converter
Bottom sieve	convertible
Brakes	mech. disc
Floating cutting platform	x
Type of cutting platform floating	gas damper